Mortar Calculator: Bags, Sand & Mix Ratio Estimator

Estimate pre-mixed 80 lb & 60 lb mortar bags, site-mix masonry cement, sand tonnage, and mixing water for concrete blocks, modular bricks, and wall square footage under ASTM C270 proportioning rules.

Estimate 1 bag of 80-lb pre-mix mortar per 30 standard 8×8×16 blocks (~3.3 bags/100 blocks) or 100–125 modular bricks. For site-mixed ASTM C270 Type S mortar, blend 1 part Portland cement, 1/2 part hydrated lime, and 3.5–4.5 parts damp sand.
Live Estimate
6Bags (80lb)(3.69 ft³)
Details

Mortar Material Estimate

Pre-Mixed 80lb Bags (Type S / N)

6

Yielding 3.69 cu ft (covers ~150 units)

Pre-Mixed 60lb

8 bags

Mixing Water

~8 gal

Site Scratch Mix (1 Cement : 3 Sand)

Cement (70lb)

2 bags

Sand (Tons)

0.24 tons

Sand (Yd³)

0.18 yd³

Total Wet Weight

0.2 Tons (480 lbs)

Mortar Volume

3.69 cu ft

ASTM C270 Field Rule

One 80 lb bag lays ~30–33 standard 8" CMU blocks or 33–35 modular clay bricks with 3/8" joints.

CMU estimates use nominal face dimensions and illustrative mortar yields (30 standard 8-inch units per 80-lb premix bag before waste; thickness adjustments apply). Confirm product yields, unit core volumes, supplier pack sizes and local prices before ordering. Reinforcement quantities are material allowances; laps, hooks, embedment and engineered design are excluded.

ASTM C270 Standards Compliant (Type M, S, N, O Mortar)
3/8" Standard Masonry Joint Calibration

ASTM C270 Mortar Proportion Specification Table

ASTM C270 specifies two distinct compliance methods: the Proportion Specification (prescribed volumetric ratios) and the Property Specification (minimum laboratory compressive strength). The table below outlines standard volumetric proportions by loose damp volume:

Mortar TypePortland CementHydrated LimeMasonry Sand (Loose)Min. Compressive StrengthTypical Application
Type M1 part1/4 part3 to 3.75 parts2,500 PSIHigh lateral & compressive loads, below-grade foundations, retaining walls
Type S1 part1/2 part3.75 to 4.5 parts1,800 PSIExterior loadbearing block walls, seismic zones, retaining walls
Type N1 part1 part5 to 6 parts750 PSIAbove-grade residential brick veneer, exterior walls, chimneys
Type O1 part2 parts7.5 to 9 parts350 PSIInterior non-load-bearing walls, historic preservation tuckpointing

Advertisement

Type N vs. Type S vs. Type M: Bag Coverage & ASTM C270 Standards

How mortar classification directly impacts masonry compressive strength, lateral bonding, and bag takeoff per 100 blocks.

The Universal Masonry Rule: 3.3 to 4 Bags (80 lb) per 100 Standard 8" CMU Blocks

For standard 8×8×16-inch hollow concrete masonry units laid with 3/8-inch face-shell joints, one 80 lb pre-blended bag yields approximately 0.67 cubic feet of wet mortar and sets 30 standard blocks (100 ÷ 30 = 3.33 bags). Ordering 4 bags of 80 lb mortar (or 5 bags of 60 lb mortar) per 100 blocks ensures full field coverage.

Type S MortarStructural Standard
1,800 PSI Compressive Strength

Best for: Exterior loadbearing walls, foundation stem walls, retaining walls, and seismic/high-wind zones. Provides maximum lateral flexural bond strength (> 130 PSI) to resist wind and earth pressure.

80 lb bags / 100 blocks:3.0 bags (with waste)
60 lb bags / 100 blocks:4.0 bags
Type N MortarAbove-Grade Veneer
750 PSI Compressive Strength

Best for: Above-grade exterior brick veneer, chimneys, parapets, soft stone, and non-bearing demising walls. Higher lime ratio delivers exceptional elasticity and workability, accommodating thermal movement without unit cracking.

80 lb bags / 100 blocks:3.0 bags (face-shell)
80 lb bags / 100 bricks:5.8 bags (full joint)
Type M MortarHeavy Below-Grade
2,500 PSI Compressive Strength

Best for: Heavy below-grade foundation walls, deep basements (> 7 ft backfill), high lateral soil thrust, manholes, retaining walls in contact with earth and water, and severe freeze-thaw exposure.

80 lb bags / 100 blocks:3.0 bags (face-shell)
Full bed bedding:5.2 bags / 100 units

Mortar Bag Takeoff by CMU Block Size (Per 100 Units with 10% Waste Buffer)

Masonry Unit & Bedding StyleNominal Dimensions80 lb Bags / 100 Units60 lb Bags / 100 UnitsWet Mortar VolumeRecommended ASTM Type
4" Partition CMU (Face-Shell)4" × 8" × 16"2.2 bags2.9 bags1.4 cu ftType N or Type S
6" Narrow CMU (Face-Shell)6" × 8" × 16"2.6 bags3.5 bags1.7 cu ftType S
8" Standard CMU (Face-Shell Standard)8" × 8" × 16"3.0 bags4.0 bags2.0 cu ftType S (Universal)
10" Foundation CMU (Face-Shell)10" × 8" × 16"3.4 bags4.5 bags2.3 cu ftType S or Type M
12" Heavy Commercial CMU (Face-Shell)12" × 8" × 16"3.8 bags5.1 bags2.5 cu ftType M or Type S
Modular Clay Facing Brick (Full Bed & Head)3-5/8" × 2-1/4" × 7-5/8"5.8 bags7.7 bags3.9 cu ftType N (Veneer)

Water Mixing & Retempering Field Rules

Water Quantity per Bag

A standard 80 lb bag requires between 4.5 to 5.5 quarts (approx 1.2 to 1.4 gallons) of clean potable water. Always add roughly 75% of water to the paddle mixer before dry ingredients, adding remaining water gradually until buttery consistency is achieved.

The 2-Hour Retempering Rule

If mixed mortar loses workability from board drying on hot sunny days, you may sprinkle fresh water and remix within the first 90 minutes. Once initial set commences (past 2 hours), retempering destroys chemical bonding; old mortar must be scrapped.

Building Specifically with Concrete Cinder Blocks?

Get block-specific coverage formulas, Quikrete brand codes (#1102 & #1122), 4"/6"/8"/12" block widths, and quick 100-block multipliers.

Cinder Block Mortar Tool
Calculation Assumptions & References Planning Reference

Material estimates depend on the selected dimensions, product yields, and waste allowance.

Content date: March 2026
Related references: ASTM C270 (Mortar), ASTM C144 (Aggregate), ASTM C90 (CMU Units), IRC Section R606. Confirm the applicable edition and local requirements.
A material estimate is not a structural design or code approval.
Masonry Q&A

Frequently Asked Questions About Masonry Mortar

Expert insights into mix ratios, bag yields, sand tonnage, and water requirements.

For an 8-inch CMU cinder block wall, you need approximately 0.036 bags (80 lb) per square foot (approx. 3.6 bags per 100 sq ft) with standard face-shell bedding. For a modular clay brick veneer wall (single wythe, ~7 bricks/sq ft), you need approximately 0.20 bags (80 lb) per square foot (approx. 20 bags per 100 sq ft) with full head and bed joints.

Advertisement